![]() ![]()
Replacement parts-When parts need replacing ensure the servicer uses parts specified by the manufacturer or parts that have the same characteristics as the original parts. Servicing-Do not attempt to service the unit beyond that described in these operating instructions. ![]() Even if the tape you use is labeled "S-VHS", the recordings you make do not use this system. The unit will automatically return to the stop mode after a pause of 5 minutes while recording. You cannot change channels while recording. To specify a time to stop recording ( page 48, The sleep timer) This unit can play tapes recorded with LP mode on other equipment ("LP" lights on the display). It takes more time for automatic tracking to work when playing tapes recorded with VP mode, and it may not work at all with some tapes. Press it again or while pressing, press to continue recording. While pressing, press to start recording. ZOOM QUICK REPLAY SPEED AUDIO TEST MIX 2CH CH SELECT RE-MASTER SUBWOOFER POSITION MEMORY PROG channel 2: channel 23: channel 123: Įach time you press the button: SP>EP>VP ^""-""""bĭ. Select the channel with the numbered buttons or. Press to put the remote control in VCR mode. Preparation Turn on the television and select the video input for the VCR. It also cancels if you stop, pause, cue, or review. (It only works if there is a five-second blank at the end of the program. Try adjusting the vertical on the television itself.Īt the end of the program, the tape rewinds to the beginning of the program and plays it again. Repeat play-play a program repeatedly Press and hold (play) for about five seconds. ![]() To return to the previous condition Press and at the same time. Preparation Press to put the remote control in DVD mode. Panasonic sb wa310 manual tv#Yes (Menu language, Audio language, Subtitle language, TV type, TV aspect) No On: You can play DVD-Video content on DVD-Audio. QUICK SETUP ( page 17) Answer questions to make basic settings.Įnable: Play HighMAT discs as HighMAT discs. The setting returns to "Off" when you remove the disc, turn the unit off or change the source. Panasonic sb wa310 manual how to#) DVD-Video Mode Select how to play pictures contained on some DVD-Audio. (Reload the disc for the setting to be effective. ) Mixed Disc-Audio & Stills Select the type of file played on discs containing both JPEG and WMA/MP3. HighMAT Play HighMAT discs as HighMAT discs, or as regular WMA/ MP3/JPEG discs. On-Screen Messages Choose whether to show on-screen messages or not. Menu Language Choose the preferred language for these menus and the onscreen messages. Off On: For clear dialog when listening at low volume. Audio during Search Choose whether to have sound during search. Dynamic Range Compression (Dolby Digital only) Change the dynamic range for late night viewing. Please check and identify the supplied accessories. System Main unit Front speakers Center speaker Surround speakers Active subwoofer Operations in these instructions are described mainly with the remote control, but you can do the operations on the main unit if the controls are the same. These operating instructions are applicable to models SC-HT790V, SC-HT800V and SC-HT810V. For optimum performance and safety, please read these instructions carefully. Positive power supply should be 10 to 12 volts.Thank you for purchasing this product. If you do a search on Google for 'LM555 circuits', you will find many examples. Please note: the 555 circuit built is an astable multivibrator circuit. The pin which gives loudest hum should be the one you want. The 555 circuit positive voltage supply is connected to a wire for probing the input connector pins one at a time. Is connected to the speaker ground via a 1K resistor (might need to decrease to 100 ohm value if you can't hear any speaker output - it will beĬlearer in a moment). Panasonic sb wa310 manual generator#Obtain/ make a simple audio generator - a LM555 timer chip would do fine.ĭesired frequency about 100 Hz (not critical). Terminal input, as I believe you indicated). Of the speaker are not directly available, you might use this alternativeĪpproach (I am assuming that you have identified the negative speaker Ohms resistance shows a direct connection. If the speaker terminals are directlyĪccessible (I presume that they may not be, by your approach), simply test resistance from positive speaker terminal to connector. Although I am not familiar with this specific speaker, I might suggest anĪpproach that, perhaps, could help. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |